Best Methods Of Stripping And Waxing Floors

stripping and waxing floors

Do you want to know the best methods of stripping and waxing floors? If your answer is yes then you are in the perfect place. Here, you will get complete information about stripping and waxing floors.

When was the last time the floors in your facility were stripped and waxed? Is it been a few months or has it been several years? Floors are often neglected; we walk on them literally. You may not realize that your floors are actually an investment, but they take daily abuse.

You must protect your investment. A floor that has been neglected for too long can end up in an irreparable state, and the cost of replacing a floor is far greater than the cost of maintaining it properly.

Here Are The Best Methods Of Stripping And Waxing Floors

stripping and waxing floors
stripping and waxing floors

When the wax coating on a flooring system has deteriorated to a level that it can no longer be polished to restore the luster, it’s time to perform these steps:

Existing Wax Strip Floors

Existing wax from floors must first be removed before a new uniform coat can be applied. The best way to do this is to install a paint remover pad on a floor polisher and apply a polishing paint remover to the floors. The goal is to remove all the old wax until only the floor surface remains.

While this is often the most laborious and time-consuming step, it is also the most important. If you don’t take the time to remove all the existing wax, when you apply the fresh wax you will end up with an uneven or cloudy floor surface.

Apply Floor Sealant

Before applying wax to freshly stripped floors, a floor sealer must first be used to protect the underlying floor surface from wax absorption.

Floor sealant helps isolate tiles and laminates from wax and it is a good idea to apply two coats of sealant to prevent wax infiltration. However, not all floor sealers are created equal, so make sure you select the right floor sealer for your flooring system.

Apply Floor Wax

With the floors stripped and sealed properly, you’re ready to apply a new coat of wax. Depending on the type of floor system you are waxing, you must choose the correct type of wax for your hard floors.

We recommend applying four to 10 coats of wax coating for a durable finish that does not require immediate removal after a few buffing sessions. However, for high-traffic areas, you may want to apply additional coats of wax.

Apply Floor Finish

With a new coat of wax on the floors, one of the last steps is to apply a coat of finish on top. This step is optional but reduces scratches and dirt buildup by protecting the underlying wax.

Polish The Floors

The last step is to buff off the new layer of wax. This removes any dust or dirt that may have built up on the top layer of wax and brings out the shine. When done regularly, floor polishing increases the life of the wax on your floors by protecting the floor surface below.

We recommend polishing low-traffic areas monthly, while high-traffic sidewalks may require weekly polishing services to look their best.

How to simplify commercial floor waxing

If the above steps seem complicated or your team doesn’t have the equipment or knowledge to remove and wax commercial hard floors, Carlson Building Maintenance experts are here to help.

We specialize in customizing a cleaning program to your specific needs to deliver results that continually exceed your expectations making your life easier. Contact cleaning marble polishing today to get started.

Faqs | Stripping And Waxing Floors

How long does it take to remove paint and wax a floor?

In general, when using a chemical stripping agent, it takes about fifteen minutes for the stripping process to stabilize before agitation is applied to the floors. After applying the wax, it hardens overnight and can be used the next day.

Can vinyl floors be stripped and waxed?

Vinyl floors can last a long time, and no matter how hard you wash them, they look no different. This is because your floors need to be removed from the top coat and then finished with the appropriate layer of wax.

How much does it cost to remove paint and wax floors?

Stripping and waxing jobs are charged per square meter. The price you charge your customer can vary due to several factors, but the national average is between 30 and 60 cents per square foot. However, some jobs can cost up to 90 cents or more depending on the difficulty of the job.


Taking the time to properly prepare to do a strip and wax will help ensure that the people in your building can avoid injuries and health complications.

By following these best practices, you and your cleaning team can perform safe and successful paint stripping and finishing procedures.

Taking the proper precautions and care when stripping and refinishing floors will also reduce insurance costs and reduce the amount spent on workers’ compensation claims.

Cleaning marble polishing offers a wide range of floor maintenance products and equipment that will make it easy to complete cleaning procedures safely and efficiently.


Leave a Comment

Your email address will not be published. Required fields are marked *